ISC 8020
Interflux® ISC 8020 is a stencil cleaning liquid for the removal of solder paste and uncured SMT adhesives in stencil printers. ISC 8020 has been designed not to interfere with solder paste rheology.
Suitable for
-
Stencil printing is the most used method to apply solder paste on the pads of a PCB (Printed Circuit Board) in the SMT (Surface Mount Technology) assembly line in electronics manufacturing. After stencil printing, SMD (Surface Mount Device) components are placed with their solderable contacts on the solder paste and the PCB is transported through a reflow oven where the components are soldered to the PCB board. Stencil printing can also be used to apply solder paste in trough holes for the Pin in Paste (PiP, intrusive reflow) technology that is meant to solder through hole components in the reflow soldering process . Stencil printing can also be used to apply SMT adhesive (glue) to the PCB board. SMD components are placed with their body on the glue that will be cured in a reflow oven. After that, the SMD components that are glued to the PCB board will be soldered in a wave soldering process. The PCB board is pressed onto a stencil that has apertures where the solder paste needs to be deposited. A volume of solder paste is present on the stencil. A squeegee is lowered onto the stencil with a certain pressure. The squeegee moves over the stencil with a certain printing speed. This will make the solder paste roll into the apertures. The printing speed can be determined by the desired throughput, typical for high volume productions but can be limited by the used solder paste. This speed can vary from 20-150 mm/s. Once the desired speed has been established, a printing pressure will have to be determined for that printing speed. Higher speeds require higher pressures. The correct printing pressure is the minimum pressure needed to get a clean stencil after printing, meaning all excessive solder paste has been removed by the squeegee. The board is moved away vertically from the stencil, the solder paste releases from the stencil and pads of the PCB have solder paste deposits. The goal is to have a well defined printing result where all solder paste has realeased from the stencil and no solderpaste has been pressed between the stencil and the PCB board. The release of the solder paste obviously is more difficult for smaller apertures and thicker stencils. Some design rules say that the ratio of the surface of the aperture to the surface of the sides ('walls') of the aperture is preferrably not smaller than 0,6. The quality of the stencil is a major parameter in good paste release. Rough sides are more likely to adhere solder paste. Different types of stencils exist. The most popular is the stainless steel stencil with laser cut apertures that are smoothened afterwards by a chemical process. Sometimes they are treated with a coating for better paste release. The main reasons for solder paste being pressed in between the stencil and the PCB board is bad sealing between board and stencil or too high printing pressure for the used printing speed. This can lead to solder balling or bridging after reflow. Some printing machines have an automated under stencil cleaning unit that can be programmed to clean the stencil after so many prints. This will facilitate a stable printing result. It is advisable not to use IPA based or water based cleaning liquids in these units as they may affect the solder paste stability. The use of products that have been specifically designed for that purpose is advisable. The stability of the solder paste on the stencil, meaning how well that the solder paste keeps its printing properties over time, is also a parameter for a stable printing process. Some printing machine have integrated AOI (Automated Optical Inspection) that will check the printing result and give an alarm if it deviates from the programmed desired values. This will help to avoid electronic units being produced with solder joints that are not according good standard.
Key advantages
-
RoHS stands for Restriction of Hazard Substances. It is a European directive: Directive 2002/95/EC. It restricts the use of some substances that are considered Substances of Very High Concern (SHVC) in electrical and electronic equipment for the territory of the European Union. A listing of these substances can be found below: Please note that this info is subject to change. Always check the website of the European Union for most recent information: https://ec.europa.eu/environment/topics/waste-and-recycling/rohs-directive_nl https://eur-lex.europa.eu/legal-content/EN/TXT/?uri=CELEX:32011L0065 1. Cadmium and cadmium compounds 2. Lead and lead compounds 3. Mercury and mercury compounds(Hg) 4. Hexavalent chromium compounds(Cr) 5. Polychlorinated biphenyls (PCB) 6. Polychlorinated naphthalenes (PCN) 7. Chlorinated paraffins (CP) 8. Other chlorinated organic compounds 9. Polybrominated biphenyls (PBB) 10. Polybrominated diphenylethers (PBDE) 11. Other brominated organic compounds 12. Organic tin compounds (Tributyl tin compounds, Triphenyl tin compounds) 13. Asbestos 14. Azo compounds 15. Formaldehyde 16. Polyvinyl chloride (PVC) and PVC blends 17. Decabrominated diphenyl ester (from 1/7/08) 18. PFOS : EU directive 76/769/EEC (not allowed in a concentration equal to or higher than 0.0005% by mass) 19. Bis(2-ethylhexyl) phthalate (DEHP) 20. Butyl benzyl phthalate (BBP) 21. Dibutyl phthalate (DBP) 22. Diisobutyl phthalate 23. Deca brominated diphenyl ester (in electrical and electronic equipment) Other countries outside of the European Union have introduced their own RoHS legislation, which is to a great extent very similar to the European RoHS.
-
Alcohol based soldering fluxes are liquid fluxes that have alcohol(s) as their principal solvent(s). The majority of liquid fluxes used in electronics manufacturing are still alcohol based. The main reasons are their historical use and hence market share and their in general larger process window compared to water based fluxes. Water based fluxes have numerous advantages to alcohol based fluxes, like lower consumption, no VOC (Volatile Organic Compound)-emmissions, no fire hazard, no need for special transport and storage, lower smell in the production area,...However a lot of electronic manufacturers seem to prefer the larger process window of alcohol based fluxes to the advantages of water based fluxes. Alcohol based fluxes in general are less sensitive to the correct spray fluxer settings to get a good flux application on the surface and in the through holes. Furthermore they are more easily evaporated in the preheating and give less risk on remaining solvent drops creating solder balls, solder splashes or bridging upon wave contact. Another parameter that is complicating the implementation of water based fluxes is that changing a flux in some cases can be a time consuming and costly process. It usually involves homologation testing and approval of end customers. Specifically for EMS (Electronic Manufacturing Servivces = subcontractors) this can be a challenge. Some countries have already implemented legislation that limits the VOC-emission of factory chimneys or imposes taxes on VOC emissions. This appears to be an extra incentive to change to water based fluxes. A recent development forced a lot of manufacturers to look into water based fluxes. The COVID-pandemia in the beginning of 2020, suddenly increased the demand for alcohol based desinfectants to that extent that at a certain moment the availability of alcohols on the market was pretty much non existing. Luckily the industry that produces alcohols was able to ramp up their volumes just in time to avoid electronic manufacturers to fall without fluxes to operate their soldering machines.