Plain Solder Wires

solder alloy

Interflux® plain solder wire for automatic solder feeding on selective soldering systems in lead-free and SnPb(Ag) alloys and in the LMPA-Q alloy. Standard diameters are 2mm and 3mm on a 4kg role.

Plain Solder Wire LMPA-Q 4kg

Suitable for

  • Selective soldering is a soldering technology in electronics manufacturing, typically used for PCB designs with mainly SMD (Surface Mount Device) components for reflow soldering and only a few through hole components that cannot pass through the reflow soldering process. These are usually thermally heavy mass components like e.g. big transfo's or thermally sensitive components like e.g. film capacitors, displays,  connectors with sensitive plastic bodies, relays, etc... The selective soldering process allows to solder these through hole components without protecting or affecting the SMD components on the bottom side of the PCB.  The selective soldering process is very flexible as the parameters can be programmed for each solder joint separately. The main limitation of the process however is the throughput or the production capacity. This can be considerately improved when using a low melting point alloy that allows for faster soldering speeds increasing production capacity up to 100% (double). The process starts with the application of a liquid flux that will deoxydize the surfaces to be soldered. This flux is applied by a micro jet or drop jet fluxer that shoots little drops. The correct calibration and programming of this fluxer is essential to get good soldering results. A common mistake is that flux is applied outside of the contact area of the soldering nozzle. This flux will remain as an unconsumed flux residue. For some fluxes and sensitive electronic circuits this can lead to increased leakage currents and failure in the field. It is advisable to use fluxes that are specifically designed for selective soldering and that are absolutely halogen free. The IPC classification for fluxes allows up to 500ppm of halogens for the lowest activitiona class but also these 500ppm can be critical, so absolutely halogen free is the key word. The next step in the process is preheating. This process step evaporates the solvents of the flux and provides heat to support good through hole wetting of the solder. Soldering is a thermal process and a certain amount of heat is needed to make a solder joint. This heat is needed from the bottom as well as from the top of the through hole component to be soldered. This heat can be provided by the preheating and by the liquid soldering alloy. Some basic machines do not have preheating, they will have to apply all heat through the liquid soldering alloy and in general they use higher temperatures for soldering. A preheating unit is usually a short wave IR (infrared) unit that applies the heat from the bottom side of the PCB. In most cases, the time and power of the preheating can be programmed. For thermally heavy boards and applications, top side preheatings exist. Usually they are hot air (convection) units where the teperature of the air can be programmed. When using this unit, it is important to know if there are any temperature sensitive components on the top side of the board that might be affected by this preheating.  Several systems for soldering exist. The one where the PCB board is standing still and only the soldering nozzle is moving is definitely preferred as all G-forces should be avoided when the solder solidifies. In the soldering step, a liquid soldering alloy is pumped through a soldering nozzle.There are different nozzle sizes and shapes available, wide nozzles, small nozzles, long nozzles and short nozzles.  Depending on the components to be soldered, one is preferred to another. In general wider nozzles and shorter nozzles give better heat transfer and are preferred. Smaller and longer nozzles can be used for situations with limited accessibility. Wettable nozzless are preferred to non wettable nozzles as they give a much more uniform flowing of the solder and more stable soldering results. Nitrogen flooding of the nozzle is advisable to have a stable flowing of the solder. The nitrogen is preferrably preheated because when not, it will cool down the solder and the PCB. The optimisation of the soldering program is essential for optimisation of the throughput/capacity of the selective soldering machine. This will focus on finding the minimal times and maximal speeds that give good through hole wetting in combination with no bridging.

  • Pre-tinning is a soldering technolgy used for wires and cables and also for the leads of some electronic and mechanical components. Pre-tinning applies a layer of solder on the surface that will provide a good solderability for the following soldering processes. The solderability of this layer is maintained very well during storage. Pre-tinning is usually done by dipping the surface to be soldered in liquid solder, that usually is a lead-free Sn(Ag)Cu alloy. Some systems use a small wave of liquid solder or a nozzle that jets liquid solder to do the pre-tinning. The pre-tinning process can be done manually but in most cases is done in an automated process. Before soldering the lead or wire is dipped in a soldering flux. To avoid flux residues after soldering, the dipping depth in the flux is usually lower or just as deep as the dipping depth in the solder. Depending on the solderability of the surfaces to be pre-tinned, different fluxes can be used. For surfaces that are hard to solder, like Ni, Zn, brass, heavily oxidized Cu,...usually water soluble fluxes are being used. They provide excellent solderability but can be and must be cleaned in a water based washing process afterwards, as the residues of these fluxes might create problems (like e.g. corrosion). For surfaces with normal solderability, IF 2005C or PacIFic 2009M can be used. The temperature of the soldering alloy is usually higher than for wave and selective soldering because this speeds up the process and the risk on damaging components is very limited. It is also possible that the dipping process needs to remove/burn off the coating of the Cu-wire to be tinned, this also requires higher temperatures. In general soldering temperatures vary from 300-450°C. These temperatures will oxydise the surface of the solder bath quite strongly. The use of Anti-Oxydant pellets can compensate for this oxydation. Some solder baths mechanically remove the top layer of the solder bath with a scraper just before the component is dipped into the solder. Dipping times very much depend on the thermal mass of the component to be soldered and usually are from 0,5s to 3s.

  • Dip soldering is a technology used to solder surfaces by dipping/immersing them in liquid solder. It is mainly used for wires and cables and also for the leads of some electronic and mechanical components. Dip soldering applies a layer of solder on the surface that will provide a good solderability for the following soldering processes. The solderability of this layer is maintained very well during storage. Dip soldering can also be used in rework and repair of a PCB (Printed Circuit Board) to e.g. remove or resolder a through hole connector. The dipping process can be done manually or by an automated process. Before soldering the lead or wire is dipped in a soldering flux. To avoid flux residues after soldering, the dipping depth in the flux is usually lower or just as deep as the dipping depth in the solder. Depending on the solderability of the surfaces to be pre-tinned, different fluxes can be used. For surfaces that are hard to solder, like Ni, Zn, brass, heavily oxidized Cu,...usually water soluble fluxes are being used. They provide excellent solderability but can be and must be cleaned in a water based washing process afterwards, as the residues of these fluxes might create problems (like e.g. corrosion). For surfaces with normal solderability IF 2005C or PacIFic 2009M can be used. The soldering alloy in most cases is Sn(Ag)Cu based. The temperature of the soldering alloy is usually higher than for wave and selective soldering because this speeds up the process and the risk on damaging components is very limited. It is also possible that the dipping process needs to remove/burn off the coating of the Cu-wire to be tinned, this also requires higher temperatures. In general soldering temperatures vary from 300-450°C. These temperatures will oxydise the surface of the solder bath quite strongly. The use of Anti-Oxydant pellets can compensate for this oxydation. Some solder baths mechanically remove the top layer of the solder bath with a scraper just before the component is dipped into the solder. Dipping times very much depend on the thermal mass of the component to be soldered and usually are from 0,5s to 3s.

  • 'Low melting point' refers to the melting point or melting range of a soldering alloy that is lower than conventional lead-free alloys which are usually Sn(Ag)Cu based alloys. The vast majority of the low melting point alloys are Bi containing because of the melting point reducing property of Bi. The main driving reason for low melting point alloys is the temperature sensitivity of some electronic components and PCB materials. Those components and materials can be damaged or predamaged by the soldering temperatures used for Sn(Ag)Cu alloys. This can lead to early failure of the electronic unit in the field which can be expensive to repair and in some cases can lead to dangerous situations. Low melting point alloys allow for substiantally lower soldering tempertures and hance reduce the risk of (pre)damaging temperature sensitive components and PCB materials. A low melting point soldering alloy like e.g. LMPA-Q requires much lower operating temperatures than the standard lead-free soldering alloys. In reflow soldering it requires a peak T° of 190°C-210°C, in wave soldering the bath temperature typically is 220°C-230°C and in selective soldering, the working temperature typically is 240°C-250°C. In reflow soldering the low melting point alloy also gives lower voiding on BTCs (Bottom Terminated Components). In general low melting point alloys have lower than 10% voiding where lead-free SAC alloys typically have 20-30% of voiding. In wave soldering the low melting point alloy allows for faster production speeds up to 70% and in selective soldering where the soldering of connectors can be done up to 50mm/s the total process time can be reduced by half, increasing the machine capacity with 100%. Furthermore the low melting point alloy does not have problems with good through hole fill on thermally heavy components. The use of nitrogen for wave and reflow soldering is possible but not required. The thermal, electrical and mechanical properties of the LMPA-Q low melting point alloy are sufficient for most electronic applications. Given all these advantages, many consider the low melting point alloys to be the future of electronics manufacturing.

  • Lead-free soldering

  •

    Lead-based soldering

Key advantages

  • LMPA stands for Low Melting Point Alloy. To find out more, go to lmpa-q.com.

  • Lead-free alloys are soldering alloys without Pb used to connect electronic components to PCB (Printed Circuit Board) boards in electronics manufacturing. In 2006 legislation restricted the use of lead (Pb) because of the risk that end-of-life electronics in land fills would pollute ground water and Pb would be introduced in the eco-system. When Pb is taken in by the human body, it is very hard to be removed and it is known to cause all kinds of (long term) health issues. In 2006 the use of lead (Pb) was restricted by legislation. For that reason, the industry was forced to look into alternatives without Pb. In the end, the industry standardised on Sn(Ag)Cu based soldering alloys. These alloys provided acceptable useability in the existing soldering processes in combination with sufficient mechanical reliabilty of the solder joints and good thermal and electrical properties. The main disadvantage of Sn(Ag)Cu alloys is their quite high melting points (or melting ranges) that result in quite high operating temperatures. This induces thermo-mechanical stress on the electronic unit in the soldering processes that can result in damage or predamage of some temperature sensitive PCB materials and components. Typical soldering temperatures in wave soldering are 250-280°C, in selective soldering 260-330°C and measured  peakT° in reflow 235-250°C. The most popular alloy is the Sn96,5Ag3Cu0,5 alloy with melting temperature around 217°C, often referred to as SAC305. Other versions are SnAg4Cu0,5, SnAg3,8Cu0,7, SnAg3,9Cu0,6,...The differences in melting point between these alloys and the differences in terms of mechanical, electrical and thermal properties are for most electronic applications and soldering processes non significant. Because of cost reasons, the one with lowest Ag-content has the preference and that is the SAC 305. Also because of cost reasons, there is a trend towards low Ag SnAgCu alloys like e.g. Sn99Ag0,3Cu0,7, Sn98,5Ag0,8Cu0,7,... often referred to as low SAC alloys. These alloys have a melting range in between 217°-227°C. This in most cases will require higher working temperatures in the soldering processes up to 10°C, which for some temperature sensitive components can be significant. The mechanical, electrical and thermal properties of the low SAC alloys differ a bit more from the standard SAC alloys. In general they have a lower thermal cycling (fatigue) resistance but for most electronics applications this is not significant. The required 10°C higher working temperature however is often a problem in reflow soldering because most electronic units will have one or more temperature sensitive components. Furthermore, in general SMD (Surface Mount Device) solder joints are weaker than through hole soldered solder joints and SAC alloys in general have rather poor thermal cycling resistance, specifically on thin solder joints. Considering all these paremeters, in most cases the choice will be made for the standard SAC alloys and not the low SAC alloys for reflow soldering. For wave soldering the story is a bit different. The wave solder bath with a lead-free soldering alloy generates quite a lot of oxides becuase of its high working temperature. This is why a lot of manufacturers chose for closed nitrogen machines. This however requires investment in infrastructure which not every manufacturer is willing or able to do. The oxides generated, in genral are being sold back to the manufacturer of the soldering alloy where they are being recycled. The total cost for the electronics manufacturer in this matter is quite high, cetainly with the high Ag soldering alloys like SAC305. That's why there is a tendency towards the use of low SAC and even SnCu alloys (without Ag). Also here the higher melting point will require an increase in operating temperature to get acceptable through hole filling. As in most cases the heat is applied from the bottom side and to the leads of the components, the temperature sensitive components on top of the board in general do not suffer too much from this. In terms of mechanical reliability of the low SAC and  SnCu alloy, this is less an issue because through hole soldered solder joints in general are much stronger than SMD joints. When (glued) SMD components are wave soldered on the bottom side of the PCB this can be different. Also when thermally heavy applications need to be soldered, the higher melting points can give a problem with good through hole fill and cases are known where the working temperature had to be raised so much that PCB material and some components from the top side were damaged. In those cases a low melting point soldering alloy is a good solution. Low melting point alloys that are SnBi based were never considered a viable alternative in the changeover from Pb containing to Pb free alloys because of there incompatibility with Pb and in the transition phase where still a lot of components and PCB materials contained Pb, it was impossible to use them. However since a couple of years the industry is starting reconsider the low melting point alloys because they have a lot of advantages and the risk on Pb contaminationhas become extremely low. A low melting point soldering alloy like e.g. LMPA-Q requires much lower operating temperatures than the standard lead-free soldering alloys. In reflow soldering it requires a peak T° of 190°C-210°C, in wave soldering the bath temperature typically is 220°C-230°C and in selective soldering, the working temperature typically is 240°C-250°C. This substantially reduces the risk of damaging temperature sensitive components and PCB materials and even facilitates the use of cheaper components and materials that are temperature sensitive. In reflow soldering the low melting point alloy also gives lower voiding on BTCs (Bottom Terminated Components). In general low melting point alloys have lower than 10% voiding where lead-free SAC alloys typically have 20-30% of voiding. In wave soldering the low melting point alloy allows for faster production speeds up to 70% and in selective soldering where the soldering of connectors can be done up to 50mm/s the total process time can be reduced by half, increasing the machine capacity with 100%. Furthermore the low melting point alloy does not have problems with good through hole fill on thermally heavy components. The use of nitrogen for wave and reflow soldering is possible but not required. The thermal, electrical and mechanical properties of the LMPA-Q low melting point alloy are sufficient for most electronic applications. Given all these advantages, many see the low melting point alloys as the future of electronics manufacturing.

  • Lead-based alloys are the traditional SnPb(Ag) based alloys that were used to connect electronic components to PCB (Printed Circuit Board) boards in electronics manufacturing before 2006. In 2006 legislation restricted the use of lead (Pb) because of the risk that end-of-life electronics in land fills would pollute groundwater and Pb would be introduced in the ecosystem. When Pb is taken in by the human body, it is very hard to be removed and it is known to cause all kinds of (long term) health issues. For this reason electronics manufacturing introduced lead-free soldering alloys. As the long term reliability of the lead-free alloys was at that point (2006) not yet established, some critical branches of the electronics industry like e.g. automotive, railway,medical, military,... were allowed to temporarily continue using the SnPb(Ag) alloys. But also in these branches the use of lead-based alloys is gradually being phased out. The most typical alloys for wave soldering were Sn60Pb40 and Sn63Pb37 with melting point around 183°C. This facilitated operating temperatures around 250°C. The oxydation behavior of the alloys was considered acceptable and the use of a closed nitrogen atmosphere like for lead-free alloys was not necessary. For reflow soldering, the most typical alloy was Sn62Pb36Ag2 with melting point around 179°C. The addition of Ag gives extra mechanical reliability to the SMD (Surface Mount Device) solder joints who are typically less strong than through solder joints. The alloy facilitated (measured) peak temperatures in between 200-230°C. The use of nitrogen in reflow was existing but certainly not as widespread as with lead-free alloys.

Physical & chemical properties

Wire diameter
2mm or 3mm
Spools
1kg or 4kg (125mm x 125mm)

Documents