WSF 7700

Suitable for

• 

  Wave soldering

  Wave soldering is a bulk soldering process used in electronics manufacturing to connect electronic components to a PCB board. The process is typically used for through hole components but can also be used for soldering of some SMD (Suface Mount Device) components that are glued with an SMT (Surface Mount Technology) adhesive to the bottom side of the PCB before passing through the wave soldering process. The wave soldering process comprises three main steps : Fluxing, preheating and soldering. A conveyor transports the PCBs through the machine. The PCBs can be mounted in a frame to avoid adjusting the conveyor width for every different PCB.  Fluxing is usually done by means of a spray fluxer but also foam fluxing and jet fluxing are possible. The liquid flux is applied from the bottomside of the PCB on the surface and in the trough holes. The purpose of the flux is to deoxydize the solderable surfaces of the PCB and components and allow the liquid soldering alloy to make an intermetallic connection with those surfaces resulting in a solder joint.   The preheating has three main functions. The solvent of the flux needs to be evaporated as it loses its function once its has been applied and it can lead to soldering defects like briding and solder balling when it contacts the solder wave in a liquid state. Water based fluxes in general need more preheating to evaporate than alcohol based fluxes. The second function of the preheating is to limit the thermal shock when the PCB contacts with the liquid solder of the solder wave. This can be important for some SMD components and PCB materials. The third function of the preheating is to promote through hole wetting of the solder. Because of the temperature difference between the PCB board and the liquid solder, the liquid solder will be cooled down when going up the through hole. Thermally heavy boards and components can draw away so much heat from the liquid solder that it is cooled down to the solidification point where it freezes before it gets to the top. This is a typical problem when using Sn(Ag)Cu alloys. A good preheating limits the temperature difference between PCB board and liquid solder and hence reduces the cool down of the liquid solder when going up the through hole. This gives a better chance that the  liquid solder will reach the top of the through hole.  In a third step the PCB board is passed over a solder wave. A bath filled with a soldering alloy is heated up to soldering temperature. This soldering temperature depends on the used soldering alloy. The liquid alloy is pumped through channels up into a wave former. There are several types of wave formers. A traditional setup is a chip wave combined with a laminar main wave. The chip wave jets solder in the direction of the PCB movement and allows to solder the back side of SMD components that are shielded of wave contact in the laminar wave by the body of the component itself is. The laminar main wave flows to the front but the adjustable back plate is positioned like this that the board will push the wave into a back flow. This will avoid the PCB being dragged through the reaction products of the soldering. A wave former that is gaining popularity is the Wörthmann-wave that combines the function of the chip wave and the main wave in one wave. This wave is more sensitive to the correct setting and bridging. Because of the fact that lead-free soldering alloys need high working temperatures and tend to oxydise quite strongly, a lot of wave soldering processes are done in a nitrogen atmosphere. A new market tendency and the considered by some as the future of soldering is the use of a low melting point alloy like e.g. LMPA-Q. LMPA-Q needs less temperature and reduces oxydation. It also has some cost related benefits like reduced electricity consumption, reduced wear ot of carriers and no need for nitrogen. It also reduces the thermal impact on electronic components and PCB materials.
• 

  Selective soldering

  Selective soldering is a soldering technology in electronics manufacturing, typically used for PCB designs with mainly SMD (Surface Mount Device) components for reflow soldering and only a few through hole components that cannot pass through the reflow soldering process. These are usually thermally heavy mass components like e.g. big transfo's or thermally sensitive components like e.g. film capacitors, displays,  connectors with sensitive plastic bodies, relays, etc... The selective soldering process allows to solder these through hole components without protecting or affecting the SMD components on the bottom side of the PCB.  The selective soldering process is very flexible as the parameters can be programmed for each solder joint separately. The main limitation of the process however is the throughput or the production capacity. This can be considerately improved when using a low melting point alloy that allows for faster soldering speeds increasing production capacity up to 100% (double). The process starts with the application of a liquid flux that will deoxydize the surfaces to be soldered. This flux is applied by a micro jet or drop jet fluxer that shoots little drops. The correct calibration and programming of this fluxer is essential to get good soldering results. A common mistake is that flux is applied outside of the contact area of the soldering nozzle. This flux will remain as an unconsumed flux residue. For some fluxes and sensitive electronic circuits this can lead to increased leakage currents and failure in the field. It is advisable to use fluxes that are specifically designed for selective soldering and that are absolutely halogen free. The IPC classification for fluxes allows up to 500ppm of halogens for the lowest activitiona class but also these 500ppm can be critical, so absolutely halogen free is the key word. The next step in the process is preheating. This process step evaporates the solvents of the flux and provides heat to support good through hole wetting of the solder. Soldering is a thermal process and a certain amount of heat is needed to make a solder joint. This heat is needed from the bottom as well as from the top of the through hole component to be soldered. This heat can be provided by the preheating and by the liquid soldering alloy. Some basic machines do not have preheating, they will have to apply all heat through the liquid soldering alloy and in general they use higher temperatures for soldering. A preheating unit is usually a short wave IR (infrared) unit that applies the heat from the bottom side of the PCB. In most cases, the time and power of the preheating can be programmed. For thermally heavy boards and applications, top side preheatings exist. Usually they are hot air (convection) units where the teperature of the air can be programmed. When using this unit, it is important to know if there are any temperature sensitive components on the top side of the board that might be affected by this preheating.  Several systems for soldering exist. The one where the PCB board is standing still and only the soldering nozzle is moving is definitely preferred as all G-forces should be avoided when the solder solidifies. In the soldering step, a liquid soldering alloy is pumped through a soldering nozzle.There are different nozzle sizes and shapes available, wide nozzles, small nozzles, long nozzles and short nozzles.  Depending on the components to be soldered, one is preferred to another. In general wider nozzles and shorter nozzles give better heat transfer and are preferred. Smaller and longer nozzles can be used for situations with limited accessibility. Wettable nozzless are preferred to non wettable nozzles as they give a much more uniform flowing of the solder and more stable soldering results. Nitrogen flooding of the nozzle is advisable to have a stable flowing of the solder. The nitrogen is preferrably preheated because when not, it will cool down the solder and the PCB. The optimisation of the soldering program is essential for optimisation of the throughput/capacity of the selective soldering machine. This will focus on finding the minimal times and maximal speeds that give good through hole wetting in combination with no bridging.

Key advantages

• 

  Absolutely halogen free

  Absolutely halogen free soldering chemistry contains no intentionally added halogens nor halides. The IPC classification allows up to 500ppm of halogens for the lowest 'L0' classification. Soldering fluxes, solder pastes and solder wires from this class are often referred to as 'halogen free'. Absolutely halogen free soldering chemistry goes one step further and does not contain this 'allowed' level of halogens. Specifically in combination with lead-free soldering alloys and on sensitive electronic applications, these low levels of halogens have been reported to cause reliability problems like e.g. too high leakage currents.  Halogens are elements from the periodic table like Cl, Br, F and I. They have the physical property that they like to react. This is very interesting from the point of view of soldering chemistry because it is intended to clean off oxides from the surfaces to be soldered. And indeed halogens perform that job very well, even hard to clean surfaces like brass, Zn, Ni,...or heavily oxidized surfaces or degraded I-Sn and OSP (Organic Surface Protection) can be soldered with the aid of halogenated fluxes. Halogens provide a great process window in solderability. The problem however is that the residues and reaction products of halogenated fluxes can be problematic for electronic circuits. They usually have high hygroscopicity and high water solubility and give an increased risk on electro migration and high leakage currents. This means a high risk on malfunctioning of the electronic circuit. Specifically with lead-free soldering alloys there are more reports that even the smallest levels of halogens can be problematic for sensitive electronic applications. Sensitive electronic applications are typically high resistance circuits, measuring circuits, high frequency circuits, sensors,...That's why the tendency is to move away from halogens in soldering chemistry in electronics manufacturing. In general when the solderability of the surfaces to be soldered from component and PCB (Printed Circuit Board) are normal, there is no need for these halogens. Smartly designed absolutely halogen free soldering products will provide a large enough process window to clean the surfaces and get a good soldering result and this in combination with high reliability residues. 
• 

  For both SnPb and lead-free processes

  In 2006 legislation restricted the use of lead (Pb) in electronics manufacturing.  However there were a lot of exemptions formulated, mainly due to the lack of long time reliablity experience with the lead-free alloys. This resulted in a lot of electronics manufacturing sites that were using both lead-free and Pb containing alloys in their soldering processes. For wave and selective soldering, a lot of electronic manufacturers desired the use of  the same flux chemistry with both types of soldering alloys. This was because they were familiar with the chemistry in terms of reliability. Also introducing new materials in a manufacturing can require a lot of paper work, extra storage capacity, etc...Although the lead-free alloys require higher operating temperatures than the Pb-containing alloys, by increasing the applied flux quantity in a lot of cases the same flux chemistry can be used for both alloys. However in some cases, usually when soldering electronic units with high thermal mass, it is not possible to use the same flux for both soldering alloys. In these cases, usually a flux with higher solid content is needed. A lot of solder wires and solder pastes are available with the same flux for both lead-free and SnPb-alloys.
• 

  RoHS compliant

  RoHS stands for Restriction of Hazard Substances. It is a European directive: Directive 2002/95/EC. It restricts the use of some substances that are considered Substances of Very High Concern (SHVC) in electrical and electronic equipment for the territory of the European Union. A listing of these substances can be found below: Please note that this info is subject to change. Always check the website of the European Union for most recent information: https://ec.europa.eu/environment/topics/waste-and-recycling/rohs-directive_nl https://eur-lex.europa.eu/legal-content/EN/TXT/?uri=CELEX:32011L0065 1. Cadmium and cadmium compounds  2. Lead and lead compounds  3. Mercury and mercury compounds(Hg)  4. Hexavalent chromium compounds(Cr)  5. Polychlorinated biphenyls (PCB)  6. Polychlorinated naphthalenes (PCN)  7. Chlorinated paraffins (CP)  8. Other chlorinated organic compounds  9. Polybrominated biphenyls (PBB)  10. Polybrominated diphenylethers (PBDE) 11. Other brominated organic compounds  12. Organic tin compounds (Tributyl tin compounds, Triphenyl tin compounds)  13. Asbestos  14. Azo compounds  15. Formaldehyde  16. Polyvinyl chloride (PVC) and PVC blends  17. Decabrominated diphenyl ester (from 1/7/08)  18. PFOS : EU directive 76/769/EEC (not allowed in a concentration equal to or higher than 0.0005% by mass) 19. Bis(2-ethylhexyl) phthalate (DEHP)  20. Butyl benzyl phthalate (BBP)  21. Dibutyl phthalate (DBP)  22. Diisobutyl phthalate 23. Deca brominated diphenyl ester (in electrical and electronic equipment) Other countries outside of the European Union have introduced their own RoHS legislation, which is to a great extent very similar to the European RoHS. 
• 

  VOC-free

  VOC stands for Volatile Organic Compound.  In general VOCs are considered non environment friendly. Some countries or regions restrict the emissions of VOCs by legislation. Alcohols are VOCs. In some cases, the use of alcohol based soldering fluxes in the wave soldering process of an electronics manufacturing can give a problem with the VOC emission restrictions. A simple solution in such a case is to use a VOC-free soldering flux. In general this is a water based flux. Beside the elimination of VOC-emmissions, water based fluxes have more advantages to alcohol based fluxes, like lower consumption, no fire hazard, no need for special transport and storage, lower smell in the production area,...However, water based fluxes in general are more sensitive to the correct spray fluxer settings to get a good flux application on the surface and in the through holes. In some cases they also might require a bit more preheating to get the water evaporated.
• 

  Increased activity

  Increased activity of a soldering product can be needed for surfaces with poor solderability like e.g. brass, unprotected Ni, Oxidised Ag, Cu that was not micro-etched,...or surfaces with degraded solderability like e.g. I-Sn that was stored too long or did see too much heat, Cu-OSP that passed a lead-free reflow profile too long ago,...An indication of the activity of a soldering product is their classification. The most popular and accepted classification for soldering products is the IPC. L0 is the lowest activation class and the standard, it should be suitable for all normal quality conventional surfaces used in electronics assembly. L1 is the lowest activation class but with a halogen content up to 0,5%. These halogens will in most cases already give a better result on many of the previously mentioned surfaces with poor or degraded solderability. The other activation classes are M0 and M1 and H0 and H1. M stands for Medium and H stands for High. 0 stands for up to 500ppm of halogens for both M0 and H0. 1 stands for up to 2% of halogens for the M1 class and for H1 more than 2% of halogens are allowed. Soldering products of the H class are to be treated with care as they can be corrosive and need to be cleaned off, preferrably in a automatised cleaning process.
• 

  Increased wetting ability

  The wetting ability of a soldering product refers to how well the activation of the soldering product is able to clean off oxides from the surfaces to be soldered. These oxides need to be removed to enable the liquid soldering alloy to penetrate the surfaces to be soldered. When the quality of the surfaces to be soldered in electronics manufacturing is normal, it is possible to use a soldering product from the lowest activation class L0. In general, only when surfaces are degraded or when the base metal is hard to solder, then a product with a higher activity or increased wetting ability is used. Such surfaces can be for example chemical Sn that was applied too thin or stored too long before soldering, components or PCB boards that were stored too long in hot and humid conditions and are heaviliy oxidised, non protected Ni, brass,... Another possible reason for using a product with increase wetting ability is ease-of-use. For example a solder wire with increased wetting ability in general will provide faster soldering and is not so sensitive to the correct handling required to produce a good hand soldered solder joint. In high volume hand soldering operations for electronc units that have not so high requirements to the residues after soldering, solder wires with increase wetting ability are often used. Also for robot soldering and laser soldering solder wires with increase wetting ability are often used because in general they have better properties for these processes.